How to Fix a Leaking Toilet Cistern (Aussie Plumber’s Guide)

DIY Plumbing Guide · Toilets

Quick answer

To fix a leaking toilet cistern, first work out how the water is escaping. If it’s getting into the toilet bowl, the seating washer at the bottom of the outlet valve has probably worn. However, if water keeps running down the overflow tube, or there’s a hissing sound coming from the cistern, the head seal in the inlet valve has most likely failed. Switch off the isolation tap, flush the toilet to drain the cistern, replace the worn washer or seal with a new one of the same type, and then turn the water supply back on gradually. Most repairs can be done within 20 to 40 minutes at a total cost of less than $10.

DifficultyBeginner+
Time20–40 min
Parts cost$4–$10
ToolsHands + towel

Running toilets are one of the most common toilet repairs Canberra homeowners call us for, and a large proportion of these problems can be fixed with a small rubber washer costing a few dollars. The difficulty lies not so much in fixing the leak, but rather in identifying which component has failed, getting the correct spare part for your particular brand and model of cistern, and understanding whether the job is something you’re allowed to do yourself. To help with all three, I’ve included diagrams of what’s inside the cistern, along with information on readily available spare parts from suppliers such as Bunnings and Reece.

Key takeaways

  • Water flowing from the cistern into the bowl in most cases means the seating washer at the bottom of the outlet valve has worn out.
  • A steady trickle down the overflow or a constant hiss could mean either a failing head seal on the inlet valve or a water level that’s set too high.
  • Do the food colouring test first. It will tell you within about 15 minutes whether there is definitely a leak in your cistern.
  • Take the old washer with you when you go to the hardware store so you know exactly what replacement to buy. Cistern washers differ depending on both the brand and the model.
  • Replacing washers or seals is generally easy enough for someone who does simple repairs around the house. However, replacing a full valve, a complete hose or the entire cistern is a job best left to a licensed plumber.

First, where is the water going?

Before you go out and buy any parts, take the lid off the cistern and watch what the water is doing for a minute or so. A cistern can only leak in a few different ways, and each of them points to a different part. Water quietly slipping into the bowl is a completely different problem from water pooling on the floor, so it’s well worth having a good look before you start taking anything apart.

Where is your toilet leaking?Water trickling into the bowl means a worn outlet valve seating washer. Water running down the overflow or a hissing cistern means the inlet valve head seal or the water level. A cistern that refills by itself means the seating washer. Water on the floor means a hose, connection or pan seal, which needs a plumber.Lift the lid. What is the water doing?Trickling intothe bowlWorn seating washeron the outlet valveRipples at the backof the pan, or awet streak down itFix 1 · DIYRunning downthe overflowInlet valve won’tshut offConstant hiss, waterlevel above theoverflow tubeFix 2 or 3 · DIYRefills by itself(“ghost flush”)Slow leak past theseating washerCistern tops up every20 minutes or so withnobody using itFix 1 · DIYWater on thefloorHose, connection,cistern or pan sealNot a washer job.Turn the isolationtap off and call usCall a plumber
The four ways a cistern leaks, and which fix in this guide matches each one.

The 15-minute food colouring test

A few drops of food colouring will show whether there is a leak inside the cistern, and Icon Water recommends this check too. It’s the same method we use while working at a customer’s home, it costs nothing and it should take no longer than about 15 minutes.

How to do the toilet dye testStep one, add a few drops of food colouring to the cistern. Step two, wait 15 minutes without flushing. Step three, check the bowl. If the water in the bowl is coloured, the cistern is leaking.1Add a few drops offood colouring2Wait 15 minutes.Don’t flush.3Colour in the bowl?Your cistern is leaking
If any colour shows up in the bowl without a flush, water is getting past a seal. Flush afterwards to clear it.

If the bowl is clear of colour but your water meter continues to creep overnight, then the leak is somewhere other than your toilet. In that case it would be worthwhile calling a plumber to locate the leak.

What’s inside your cistern

Nearly all contemporary Australian cisterns are the same when it comes to their two working components. The inlet valve allows water into the cistern and automatically closes when the cistern is full. The outlet valve sits in the centre and connects to the flush button on your toilet. It rises when you press the button and then returns to its sealing position at the base of the tank, where it sits on a rubber or silicone seating washer. Although brands such as Caroma, Fowler, Geberit and Fix-A-Loo have slightly different designs, they all operate on the same principle.

Inside a dual flush toilet cisternCutaway of a cistern showing the flush button, the inlet valve with its float and head seal, the water level line, the outlet valve with its overflow, the seating washer at the base of the outlet valve, the isolation tap and flexible hose, and the flush pipe to the pan.1Flush buttonOften unscrews before the lid lifts.2Inlet valve capUnclips or twists off to reach the seal.3Head sealWorn seal = cistern won’t stop filling.4FloatRises with the water and shuts the valve.5Water lineShould sit below the top of the overflow.6Outlet valve + overflowLifts to flush. Overflow sends excess to the pan.7Seating washerSeals the base. Worn = trickle into the bowl.8Isolation tap + flexi hoseTurn clockwise to stop water to the toilet.9Flush pipe to panLeaks here or at the base need a plumber.
A typical close-coupled dual flush cistern. The two parts that cause most leaks are the head seal (3) and the seating washer (7).

Symptom, cause and the part you need

Compare what you’re seeing with the most likely causes in the table below. In our experience, the first two rows account for the vast majority of leaking cisterns we come across in Canberra homes.

What you notice Most likely cause Part to buy DIY?
Trickle or ripple into the bowl, dye test positive Worn or dirty seating washer Seating washer to suit your outlet valve Yes
Water running down the overflow, constant hiss Worn inlet valve head seal Inlet valve head seal Yes
Water level sits above the overflow Float set too high Nothing, just adjust it Yes
Cistern refills by itself every so often Slow leak past the seating washer Seating washer Yes
Very slow fill or whistling Blocked filter or failing inlet valve New inlet valve Plumber
Button sticks or flush won’t stop Worn outlet valve or button linkage New outlet valve Plumber
Water on the floor Hose, connection, cistern or pan seal Depends on the leak Plumber

Fix 1 · Replace the outlet valve seating washer

This is the fix for water leaking into the bowl. The seating washer is a sealing ring of rubber or silicone that fits under the outlet valve and seals the hole in the bottom of the cistern. Over time it becomes hardened or warped, or picks up grit, and that allows water to leak around it.

  1. Turn off the water at the isolation tap

    You’ll find the isolation tap behind or next to the toilet, and it looks like a small chrome tap. Turn it clockwise until it won’t move any further, then flush the toilet to drain the cistern. Some water may still be left at the bottom, so have a towel ready to mop up the excess.

  2. Take off the button and lid

    There are a few different ways to get into a cistern. On most dual flush toilets there’s a button that has to come off before you can remove the lid, and usually you do this by unscrewing the button ring anticlockwise. Place the lid somewhere safe where it won’t break, because ceramic lids are very prone to chipping when they’re dropped.

  3. Remove the outlet valve

    This part can be tricky depending on what type of outlet valve your toilet has. Typically you need to twist the outlet valve a quarter turn anticlockwise, or sometimes you need to release a clip that holds the valve in place. Take a picture of the valve assembly before removing it, so you’ll know how everything fits back together again. If the valve is made of old, brittle plastic, be careful, because if you snap it you’ll need to call a plumber.

  4. Swap the seating washer

    Flip the outlet valve upside down and carefully peel off the old washer from the bottom of the valve. Clean out any debris that has built up in the groove, then press the new washer onto the underside of the valve, making sure it is perfectly flat and centred. A slight misalignment can cause continued leakage, so take your time with this step.

  5. Clean the seat in the cistern

    Using a soft cloth, wipe away any debris or mineral build-up around the outlet hole in the bottom of the cistern. Do not use steel wool or any other abrasive cleaning tool, because a roughed-up surface will continue to let water leak through even after you’ve installed a new washer.

  6. Refit, turn the water on and test

    Replace the outlet valve and make sure it is securely locked in place. Reattach the button, then slowly open the isolation tap and allow the cistern to refill. After several flushes, do another dye test to make sure no more water is leaking into the bowl.

From the van · Ethan’s tip

Washers tend to stretch and swell with age, which means an old one can look larger than the size you actually need. If possible, take both the old washer and the entire outlet valve to the store so you can compare them side by side. If you’re still not sure, choose the slightly smaller option, because a new washer that is too big will buckle and leak.

Fix 2 · Replace the inlet valve head seal

If water continues to flow into the cistern and you can see it spilling over into the overflow pipe, the inlet valve is not shutting off. In many cases the issue with modern valves is a damaged head seal, which is a small rubber or silicone washer located in the cap at the top of the valve.

  1. Isolate and empty the cistern

    As explained before, shut off the isolation tap, flush the toilet and lift off the lid of the cistern. Place a towel under the valve, since some water will run out when you open it.

  2. Open the valve cap

    The caps on top of most brands of inlet valve twist off with a quarter turn, or they simply snap off. There’s no need to remove the entire valve from the cistern, which is why this type of job remains DIY friendly.

  3. Replace the head seal and clear any grit

    Remove the old head seal and check it for sand or grit, as this is a very common reason seals stop working. Place the new head seal in exactly the same position as the old one, then put the cap back onto the valve until it snaps or locks into place.

  4. Turn on slowly and check the level

    Slowly turn on the isolation tap and watch how the cistern fills. The valve should shut off once the water reaches the right level, below the top of the overflow. If it continues to run, the valve has likely deteriorated beyond repair and needs to be replaced.

Fix 3 · Adjust the water level

At times there’s absolutely nothing wrong with the valve, and the float is simply set too high, so as soon as the cistern fills up, water spills into the overflow. Many modern inlet valves have an adjuster screw or a clip on the float arm. Lower the float a little at a time and flush after each adjustment. Keep adjusting until the water stops just below the level mark inside the cistern, or sits approximately 20 to 25mm below the top of the overflow if there’s no mark to go by.

Not sure which part your cistern needs?

If you’d like to know what’s causing your cistern problem, send us a picture of the inside of your cistern. Our toilet repair team handles everything from changing washers to swapping out entire inlet valves, every week.

Call Ethan0423 491 249

Parts you’ll need and where to buy them in Canberra

The first three parts below are easy to fit yourself as a DIY repair. Underneath them are the valves a licensed plumber would install if replacing the washers doesn’t fix the problem. Prices are from Bunnings at the time of writing, so check before you head out because they can change.

DIY washers and seals

DIYFIX-A-LOO Cistern Repair KitOne inlet head seal plus one silicone seating washer. Suits many Caroma, Fowler and Geberit cisterns made after 2005.$9.45 Bunnings · I/N 0436354View at Bunnings

DIYFIX-A-LOO Seating Washer (Caroma Duoflo)Silicone, 66mm outside and 25mm inside diameter. Suits Caroma Duoflo outlet valves from 1995 to 2005.$3.64 Bunnings · I/N 0130541View at Bunnings

DIYKinetic Inlet Valve HeadsealReplaces a worn head seal in the inlet valve. Take the old one in to match it.$5.56 Bunnings · I/N 4750206View at Bunnings

Full valves (fitted by a licensed plumber)

PlumberFIX-A-LOO Hush Fill Bottom Entry Inlet ValveWaterMark approved, quiet fill, adjustable water level and a 12 year warranty. For bottom entry cisterns.$26.95 Bunnings · I/N 0422772View at Bunnings

PlumberUniversal Slimline Inlet ValveA slim replacement inlet valve for tighter cisterns.$22.98 Bunnings · I/N 1162185View at Bunnings

PlumberFIX-A-LOO Thunderflush Dual Flush Outlet ValveThe closest Bunnings equivalent to many older Caroma square dual flush valves.Check price Bunnings · I/N 4790780View at Bunnings

Where to buy in Canberra

Fix-A-Loo and Kinetic generic parts are readily available from Bunnings, and the staff can typically find a matching washer if you bring the original in. For genuine Caroma, Fowler or Geberit parts, you’ll have to go to a plumbing supplier, such as Reece, with branches in Fyshwick, Belconnen, Braddon and Phillip, or Tradelink in Fyshwick, which is open to the public. Take the old washer with you, along with a photo of the inside of your cistern showing the brand name if possible.

Should you use genuine or generic washers? Generic washers generally work just fine for most older Caroma and Fowler cisterns. With newer models, especially those installed in walls, genuine parts may be worth the extra money, because they’re made specifically for that model and tend to give a better seal that lasts longer.

What about in-wall (concealed) cisterns?

If you have a flush plate on the wall instead of a visible cistern, for example a Caroma Invisi or a Geberit system, then essentially the same two components are working for you behind the plate. To get to them, you remove the button plate and the access panel behind it. Because there’s so little room, unless you feel absolutely confident, we’d recommend having a plumber do this type of repair. On these systems a constant ripple in the bowl or a cistern that refills every 20 minutes or so usually points to the outlet valve seal.

Common mistakes we get called out to fix

  • Buying the wrong washer. Cistern washers can look almost identical but differ between brands and ages, so always match the new one to the old one.
  • Fitting the washer off-centre. A washer that isn’t sitting exactly in the middle will keep leaking, even if it’s brand new.
  • Cleaning the seat with something abrasive. Any scratches on the seat give water a direct path around the washer.
  • Forcing old plastic. Brittle valve parts can crack under slight pressure, and a broken outlet valve means a full replacement.
  • Overtightening the isolation tap or hose. Cranking these too hard can damage the fittings and turn a small drip into a much bigger leak on the floor.
From the van · The job we see most

The majority of calls we receive begin when someone has bought two separate washers for their cistern but the problem still hasn’t gone away. Normally it’s the correct washer positioned just off centre, or debris sitting on the seat that gives the water a direct path around the washer. Sometimes the ageing plastic of the outlet valve has warped, and then the whole valve needs replacing. Many people spend hours trying to sort out their washers before calling us, and we often find that a quick inspection resolves the issue faster and more cheaply than continuing to buy more parts.

Australian plumbing regulators commonly allow homeowners to repair or replace a drop valve washer, float valve washer or seating washer in a toilet cistern, which covers Fix 1, Fix 2 and Fix 3 in this guide. Replacing a whole inlet or outlet valve, the flexible hose, the isolation tap or the cistern itself involves the water supply, and in the ACT that is generally work for a licensed plumber.

Job DIY OK?
Replace a seating washer or head seal Generally yes
Adjust the float or water level Yes
Replace a whole inlet or outlet valve Licensed plumber
Replace the flexi hose or isolation tap Licensed plumber
Replace the cistern or fix a leak at the pan Licensed plumber

This is general information, not legal advice. If you’re unsure, check with Access Canberra or your local regulator.

How much water does a leaking cistern waste?

A toilet cistern leak can waste even more water than a dripping tap. According to Sydney Water, a barely noticeable cistern leak uses approximately 9 litres per day, while a leak with a continuous hiss can lose around 261 litres daily. Over the course of a year the total can be substantial, and all of that wasted water is billed by Icon Water.

Litres wasted per year by a leaking toilet cisternA slow, barely visible leak wastes about 3,285 litres a year. A leak visible in the pan wastes about 13,140 litres. A visible, just audible leak wastes about 52,560 litres. A constant hiss wastes about 95,265 litres a year.Litres wasted per year by one leaking cisternYearly totals from Sydney Water daily estimatesSlow, barely visible9 L/day3,285 LVisible in the pan36 L/day13,140 LVisible, just audible144 L/day52,560 LConstant hiss261 L/day95,265 L
Daily leak rates from Sydney Water, multiplied out to a full year.

When to call a plumber instead

In general, replacing a cistern washer should fix most types of leaks. However, when any of the following occur, it’s probably best to contact a licensed plumber.

  • There is visible water on the floor near the cistern, the hose or the base of the pan
  • The dye test continues to show colour after you’ve replaced the washer
  • The inlet valve does not close completely, even with a new head seal
  • The outlet valve or button is cracked, stuck or misshapen
  • The cistern is located inside a wall and you’re uncomfortable opening it
  • The isolation tap has seized or is leaking

Our team handles toilet repairs, as well as inlet and outlet valve replacements and blocked toilets, throughout Belconnen, Tuggeranong, Queanbeyan and the surrounding suburbs. If you also have a dripping tap, our guide on how to change a tap washer has everything you need.

Toilet still running?

We’re licensed, local and upfront, and Ethan looks after Canberra, Belconnen, Tuggeranong, Queanbeyan and the surrounding areas for toilet repairs, cistern parts and blocked toilets.

Call 0423 491 249ACT Lic. 20181262

Leaking cistern FAQs

Why does my toilet keep running after I flush?

In most cases it’s because the outlet valve isn’t sealing properly after the flush, so water keeps leaking into the bowl and the inlet valve keeps topping the cistern up. A worn or dirty seating washer is the most common reason. If the water is running down the overflow instead, the problem is likely to be the inlet valve head seal or the water level.

Why is water trickling into my toilet bowl?

A continuous trickle into the bowl usually means the seating washer underneath the outlet valve is worn, warped or has some grit stuck under it. Most of the time, replacing the washer and cleaning the seat is all it takes.

Can I fix a leaking toilet cistern myself in Canberra?

Generally, yes, as long as you’re only replacing washers or seals or adjusting the water level. Replacing a whole inlet or outlet valve, the hose, the isolation tap or the cistern itself is generally work for a licensed plumber in the ACT.

What seating washer do I need for my cistern?

The right seating washer depends on the brand and age of your outlet valve. Take the old washer, or the outlet valve itself, to Bunnings or a plumbing supplier and compare them side by side. Old washers tend to stretch, so the correct replacement can look slightly smaller.

Why does my toilet refill by itself every so often?

This is often called a ghost flush. Water is slowly seeping past the seating washer into the bowl until the level drops far enough to trigger the inlet valve. In most cases a new seating washer will stop it.

How much does it cost to fix a leaking cistern?

If you do it yourself, a new washer or seal usually costs somewhere between $4 and $10. If you need a new inlet or outlet valve fitted, a plumber’s price will depend on the part and your cistern, so it’s worth getting a quote first.

How long do cistern washers last?

Washers can last for many years, although chlorine, cleaning tablets that sit in the cistern and grit in the water supply can all shorten their life. If you find yourself replacing them often, the valve or the seat itself may be worn.

Is a toilet leaking from the base the same problem?

No. Leaks around the base of the toilet usually have nothing to do with the parts inside the cistern. They’re generally caused by the pan connector, the flush pipe seal or a supply connection, and they need a licensed plumber.

About the author · Ethan, Born Plumbing

Ethan has more than 10 years of plumbing experience. His ACT licence number is 20181262 and his NSW licence number is 359989C, and he’s a member of Master Plumbers ACT. He and the rest of the Born Plumbing team look after toilet repairs, leaking taps, hot water systems and blocked drains throughout Canberra and Queanbeyan.

Sources

  1. Icon Water: Leaks (food colouring test)
  2. Sydney Water: Water use and conservation (cistern leak rates)
  3. QBCC (homeowner cistern washer work)
  4. Bunnings product listings, prices checked November 2026
  5. Born Plumbing on-site experience, Canberra and Queanbeyan

Get A Quick Quote